This article is about a PC processor socket.
For SLOT-1 on a Nintendo DS, see.
Predecessor Successor This article is part of the series Pentium II SECC form installed into Slot 1 Slot 1 refers to the physical and electrical specification for the connector used by some of 's microprocessors, including the, and the.
Both single and dual processor configurations were implemented.
Intel switched back to the traditional socket interface with in 1999.
Previously with theIntel had combined processor and cache dies in the same package.
Unfortunately, this method required that the two components be bonded together early in the production process, before testing was possible.
As a result, a single, tiny flaw in either die made it necessary to discard the entire assembly, 3 money top up low production yield and high cost.
Intel subsequently designed a circuit board where the CPU and cache remained closely integrated, but were mounted on acalled a Single-Edged Contact Cartridge SECC.
The CPU and cache could be tested separately, before final assembly into a package, reducing cost and making the CPU more attractive to markets other than that of high-end servers.
These cards could also be easily plugged into a Slot 1, thereby eliminating the chance for pins of a typical CPU to be bent or broken when installing in a socket.
The form factor used for Slot 1 was a 5-inch-long, 242-contact named Bookies slots best />To prevent the cartridge from being inserted the wrong way, the slot was keyed to allow installation in only one direction.
The SC242 was later used for AMD's as well, and while the two slots were identical mechanically, they were electrically incompatible.
To discourage Slot A confirm. best luxor slot machines opinion 3 money top up trying to install a Slot 1 CPU, the connector was rotated 180 degrees on Slot A motherboards.
With the new Slot 1, Intel added support for SMP.
A maximum of two Best dual slot 1 motherboard II or Pentium III CPUs can be used in a dual slot motherboard.
The Celeron does not go here official SMP support.
There are also converter link, known aswhich hold a so that a CPU can be used with Slot 1 motherboards.
These specific converters, however, are rare.
Another kind of slotket allows using 3 money top up Socket 370 CPU in a Slot 1.
Many of these latter devices are equipped with own voltage regulator modules, in order to supply the new CPU with a lower core voltage, which the motherboard would not otherwise allow.
Inside the cartridge, the CPU itself is enclosed in a hybrid plastic and metal case.
The back of the housing is plastic and has several markings on it: the name, "Pentium II"; the Intel logo; a ; and the model number.
The front consists of a black aluminum plate, which is used to hold the CPU cooler.
The SECC form is very solid, because the CPU itself is resting safely inside the case.
As compared to socket-based CPUs, there are no pins that can be bent, and the CPU is less likely to be damaged by improper installation of a cooler.
Following SECC, the SEPP-form Single Edge Processor Source appeared on the market.
It was designed for lower-priced Celeron CPUs.
This form lacks a case entirely, consisting solely of the printed-circuit board holding the components.
A form factor called SECC2 was used for late Pentium II and Pentium III CPUs for Slot 1, which was created to accommodate the switch to packaging.
Only the front plate was carried over, the coolers were now mounted straight to the PCB and exposed CPU die and are, as such, incompatible with SECC cartridges.
Slot 1 is a successor to.
While the Socket 8 CPUs Pentium Pro directly had the L2-cache embedded into the CPU, it is located outside of the core on a circuit board shared with the core itself.
The exception is later Slot 1 CPUs with the core which have the L2-Cache embedded into the die.
In the beginning best dual slot 1 motherboard 2000, while the Pentium-III-CPUs with -housing appeared, Slot 1 was slowly succeeded byafter Intel had already offered Socket 370 and Slot 1 at the same time since the beginning of 1999.
Socket 370 was initially made for the low-cost Celeron processors, while Slot 1 was thought of as a platform for the expensive Pentium II and early Pentium III models.
Cache and core were both embedded into the die.
Slot 1 also obsoleted the oldat least regarding Intel, as the standard platform for the home-user.
After superseding the Intel CPU, Intel completely left the Socket 7 market.
By using this site, you agree to the and.
Wikipedia® is a registered trademark of thea non-profit organization.
Ultimate $20,000 Dual System Build – Corsair Slate Part 2
Like the ROG Strix board listed above, the X470 AORUS ULTRA GAMING motherboard can accommodate dual GPU configurations, as well as up to 64GB of RAM. It also has an M.2 slot (and so you can use an NVME SSD on this motherboard) and plenty of RGB options/ports to help you light up your build.
It is an amusing phrase
I apologise, but, in my opinion, you are not right. I am assured. Write to me in PM, we will communicate.
I recommend to you to visit a site on which there are many articles on a theme interesting you.
Bravo, what necessary phrase..., a brilliant idea
You are mistaken. I can prove it. Write to me in PM.